Bertazzoni PM36 3 0G X Manuel d'installation télécharger pdf (Page 6)

A label on the last page of this manual and on the lower part of the case indicates the conditions for

regulating the appliance: type of gas and pressure used.

IMPORTANT: This appliance must be installed in accordance with the norms in force of the country

concerned and it must only be used in a well-ventilated place.

ATTENTION: Remember that the gas inlet connection for the appliance is threaded 1/2 gas cylindrical

male in accordance with the norms UNI-ISO 228-1. (Fig. 6-7)

There are two ways to make the connection to the main gas line:

A. The hotplate can be connected with rigid pipe as specified in AS5601 table 3.1.

B. The hotplate can be connected with a Flexible Hose, which complies with AS/NZS 1869 (AGA Approved),

10mm ID, class B or D, no more than 1.2m long and in accordance with AS5601.

WARNING: Ensure that the hose assembly is restrained from accidental contact with the flue or flue outlet of

an underbench oven and it does not contact the hot surfaces of the hotplate, oven, dishwasher or other

separate appliance that may be installed underneath or next to the hotplate. The hose should not be

subjected to abrasion, kinking or permanent deformation and should be able to be inspected along its entire

length. Unions compatible with the hose fittings must be used and connections tested for gas leaks.

The supply connection point must be accessible with the appliance installed. Fit the supplied elbow and

gasket as shown in Fig.20. The gas inlet connection has a 1/2" BSP male thread. When making the

connection, take care not to apply excessive stress by counterbalancing tightening force. Ensure that the

available gas supply is the same as the gas type label affixed to the base of the hob. If not, contact

Bertazzoni for a Gas Conversion Kit. The gas supply pressure must be adjusted in accordance with the data

label for the gas type.

Natural Gas

The natural gas regulator supplied must be fitted for natural gas. Ensure the arrow on the regulator points

towards the direction of the gas flow. The test point pressure must be adjusted to 1.00 kPa with the largest

burner operating on maximum flame.

Propane Gas

Fit the Propane Gas test point assembly (supplied in the gas conversion kit). An AGA Approved gas

regulator suitable for a supply pressure of 2.75kPa should be part of the gas tank supply.

Electrical connection

Connection to the electricity supply must be carried out according to the norms and indications of

the law in force.

Before carrying out the connection check that:

- The electric charge of the system and the sockets are suitable for the maximum power of the appliance

(see label on the lower part of the case).

- The socket or system is equipped with an efficient earth connection according to the norms and indications

of the law currently in force. No responsibility can be held if these indications are not respected.

When the connection to the electricity supply is made with a socket.

Fit onto the electric cable a standard plug ( if it is not provided ) which is appropriate for the charge indicated

on the label. Connect up the wires according to the diagram in Fig. 10 taking care to respect the

corresponding pairs listed below:

letter L (phase) = brown coloured wire;

letter N (neutral) = blue coloured wire;

symbol”

” earth = green-yellow coloured wire;

- The electric cable must be positioned so that it cannot reach a temperature of over 75 K at any point.

- Do not use reducers, adapters or shunts for the connection as they could cause false contacts and

subsequent dangerous overheating.

WARNING: The plug must be made accessible after installation for easy servicing and maintenance.

WARNING: If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a

similarly qualified person in order to avoid a hazard.

1 2 3 4 5 6 7 8 9 10 11 ... 18 19

Commentaires sur ces manuels

Pas de commentaire

Bertazzoni PM36 3 0G X Manuel d'installation Page 6

Commentaires sur ces manuels

Produits connexes et manuels pour Plaques chauffantes Bertazzoni PM36 3 0G X